- Perform routine photovoltaic (PV) system maintenance on modules, arrays, batteries, power conditioning equipment, safety systems, structural systems, weather sealing, or balance of systems equipment.
Occupations with related tasks Save Table: XLSX CSV
- Assemble, install, repair, and maintain elevators, escalators, moving sidewalks, and dumbwaiters, using hand and power tools, and testing devices such as test lamps, ammeters, and voltmeters.
- Disassemble defective units, and repair or replace parts such as locks, gears, cables, and electric wiring.
- Adjust safety controls, counterweights, door mechanisms, and components such as valves, ratchets, seals, and brake linings.
- Inspect wiring connections, control panel hookups, door installations, and alignments and clearances of cars and hoistways to ensure that equipment will operate properly.
- Check that safety regulations and building codes are met, and complete service reports verifying conformance to standards.
- Locate malfunctions in brakes, motors, switches, and signal and control systems, using test equipment.
- Read and interpret blueprints to determine the layout of system components, frameworks, and foundations, and to select installation equipment.
- Connect car frames to counterweights, using steel cables.
- Maintain log books that detail all repairs and checks performed.
- Connect electrical wiring to control panels and electric motors.
- Test newly installed equipment to ensure that it meets specifications, such as stopping at floors for set amounts of time.
- Participate in additional training to keep skills up to date.
- Operate elevators to determine power demands, and test power consumption to detect overload factors.
- Install electrical wires and controls by attaching conduit along shaft walls from floor to floor and pulling plastic-covered wires through the conduit.
- Attach guide shoes and rollers to minimize the lateral motion of cars as they travel through shafts.
- Install outer doors and door frames at elevator entrances on each floor of a structure.
- Assemble elevator cars, installing each car's platform, walls, and doors.
- Bolt or weld steel rails to the walls of shafts to guide elevators, working from scaffolding or platforms.
- Assemble electrically powered stairs, steel frameworks, and tracks, and install associated motors and electrical wiring.
- Cut prefabricated sections of framework, rails, and other components to specified dimensions.
- Assemble, install, repair, and maintain elevators, escalators, moving sidewalks, and dumbwaiters, using hand and power tools, and testing devices such as test lamps, ammeters, and voltmeters.
- Disassemble defective units, and repair or replace parts such as locks, gears, cables, and electric wiring.
- Adjust safety controls, counterweights, door mechanisms, and components such as valves, ratchets, seals, and brake linings.
- Repair or adjust track switches, using wrenches and replacement parts.
- Dress and reshape worn or damaged railroad switch points or frogs, using portable power grinders.
- Lubricate machines, change oil, or fill hydraulic reservoirs to specified levels.
- Clean or make minor repairs to machines or equipment.
- Patrol assigned track sections so that damaged or broken track can be located and reported.
- Weld sections of track together, such as switch points and frogs.
- Observe leveling indicator arms to verify levelness and alignment of tracks.
- Operate single- or multiple-head spike driving machines to drive spikes into ties and secure rails.
- Operate track wrenches to tighten or loosen bolts at joints that hold ends of rails together.
- Cut rails to specified lengths, using rail saws.
- Drill holes through rails, tie plates, or fishplates for insertion of bolts or spikes, using power drills.
- Clean tracks or clear ice or snow from tracks or switch boxes.
- Clean, grade, or level ballast on railroad tracks.
- Raise rails, using hydraulic jacks, to allow for tie removal and replacement.
- Adjust controls of machines that spread, shape, raise, level, or align track, according to specifications.
- Grind ends of new or worn rails to attain smooth joints, using portable grinders.
- Operate single- or multiple-head spike pullers to pull old spikes from ties.
- String and attach wire-guidelines machine to rails so that tracks or rails can be aligned or leveled.
- Engage mechanisms that lay tracks or rails to specified gauges.
- Drive graders, tamping machines, brooms, or ballast spreading machines to redistribute gravel or ballast between rails.
- Drive vehicles that automatically move and lay tracks or rails over sections of track to be constructed, repaired, or maintained.
- Turn wheels of machines, using lever controls, to adjust guidelines for track alignments or grades, following specifications.
- Push controls to close grasping devices on track or rail sections so that they can be raised or moved.
- Operate tie-adzing machines to cut ties and permit insertion of fishplates that hold rails.
- Paint railroad signs, such as speed limits or gate-crossing warnings.
- Spray ties, fishplates, or joints with oil to protect them from weathering.
- Repair or adjust track switches, using wrenches and replacement parts.
- Dress and reshape worn or damaged railroad switch points or frogs, using portable power grinders.
- Lubricate machines, change oil, or fill hydraulic reservoirs to specified levels.
- Clean or make minor repairs to machines or equipment.
- Dismantle and repair oil field machinery, boilers, and steam engine parts, using hand tools and power tools.
- Walk flow lines to locate leaks, using electronic detectors and by making visual inspections, and repair the leaks.
- Unscrew or tighten pipes, casing, tubing, and pump rods, using hand and power wrenches and tongs.
- Guide cranes to move loads about decks.
- Lay gas and oil pipelines.
- Bolt together pump and engine parts.
- Move pipes to and from trucks, using truck winches and motorized lifts, or by hand.
- Clean trucks used in the fields.
- Dig holes, set forms, and mix and pour concrete into forms to make foundations for wood or steel derricks.
- Supply equipment to rig floors as requested and provide assistance to roughnecks.
- Clean up spilled oil by bailing it into barrels.
- Dig drainage ditches around wells and storage tanks.
- Cut down and remove trees and brush to clear drill sites, to reduce fire hazards, and to make way for roads to sites.
- Dismantle and repair oil field machinery, boilers, and steam engine parts, using hand tools and power tools.
- Walk flow lines to locate leaks, using electronic detectors and by making visual inspections, and repair the leaks.
- Rotate cleaning rods manually, using turning pins.
- Service, adjust, and make minor repairs to equipment, machines, and attachments.
- Communicate with supervisors and other workers, using equipment such as wireless phones, pagers, or radio telephones.
- Drive trucks to transport crews, materials, and equipment.
- Inspect manholes to locate sewer line stoppages.
- Operate sewer cleaning equipment, including power rodders, high-velocity water jets, sewer flushers, bucket machines, wayne balls, and vac-alls.
- Prepare and keep records of actions taken, including maintenance and repair work.
- Clean and repair septic tanks, sewer lines, or related structures such as manholes, culverts, and catch basins.
- Measure excavation sites, using plumbers' snakes, tapelines, or lengths of cutting heads within sewers, and mark areas for digging.
- Locate problems, using specially designed equipment, and mark where digging must occur to reach damaged tanks or pipes.
- Dig out sewer lines manually, using shovels.
- Clean and disinfect domestic basements and other areas flooded by sewer stoppages.
- Withdraw cables from pipes and examine them for evidence of mud, roots, grease, and other deposits indicating broken or clogged sewer lines.
- Ensure that repaired sewer line joints are tightly sealed before backfilling begins.
- Install rotary knives on flexible cables mounted on machine reels, according to the diameters of pipes to be cleaned.
- Start machines to feed revolving cables or rods into openings, stopping machines and changing knives to conform to pipe sizes.
- Update sewer maps and manhole charts.
- Cover repaired pipes with dirt, and pack backfilled excavations, using air and gasoline tampers.
- Cut damaged sections of pipe with cutters, remove broken sections from ditches, and replace pipe sections, using pipe sleeves.
- Requisition or order tools and equipment.
- Break asphalt and other pavement so that pipes can be accessed, using airhammers, picks, and shovels.
- Tap mainline sewers to install sewer saddles.
- Rotate cleaning rods manually, using turning pins.
- Service, adjust, and make minor repairs to equipment, machines, and attachments.
- Perform routine maintenance on delivery vehicles, such as monitoring fluid levels and replenishing fuel.
- Deliver and pick up medical records, lab specimens, and medications to and from hospitals and other medical facilities.
- Obtain signatures and payments, or arrange for recipients to make payments.
- Record information, such as items received and delivered and recipients' responses to messages.
- Receive messages or materials to be delivered, and information on recipients, such as names, addresses, telephone numbers, and delivery instructions, communicated via telephone, two-way radio, or in person.
- Load vehicles with listed goods, ensuring goods are loaded correctly and taking precautions with hazardous goods.
- Walk, ride bicycles, drive vehicles, or use public conveyances to reach destinations to deliver messages or materials.
- Sort items to be delivered according to the delivery route.
- Deliver messages and items, such as newspapers, documents, and packages, between establishment departments and to other establishments and private homes.
- Unload and sort items collected along delivery routes.
- Plan and follow the most efficient routes for delivering goods.
- Check with home offices after completed deliveries to confirm deliveries and collections and to receive instructions for other deliveries.
- Collect, seal, and stamp outgoing mail, using postage meters and envelope sealers.
- Use telephone to deliver verbal messages.
- Perform general office or clerical work, such as filing materials, operating duplicating machines, or running errands.
- Perform routine maintenance on delivery vehicles, such as monitoring fluid levels and replenishing fuel.
- Repair or replace defective pressure vessel parts, such as safety valves or regulators, using torches, jacks, caulking hammers, power saws, threading dies, welding equipment, or metalworking machinery.
- Attach rigging and signal crane or hoist operators to lift heavy frame and plate sections or other parts into place.
- Study blueprints to determine locations, relationships, or dimensions of parts.
- Locate and mark reference points for columns or plates on boiler foundations, following blueprints and using straightedges, squares, transits, or measuring instruments.
- Bolt or arc weld pressure vessel structures and parts together, using wrenches or welding equipment.
- Position, align, and secure structural parts or related assemblies to boiler frames, tanks, or vats of pressure vessels, following blueprints.
- Install manholes, handholes, taps, tubes, valves, gauges, or feedwater connections in drums of water tube boilers, using hand tools.
- Shape or fabricate parts, such as stacks, uptakes, or chutes, to adapt pressure vessels, heat exchangers, or piping to premises, using heavy-metalworking machines such as brakes, rolls, or drill presses.
- Assemble large vessels in an on-site fabrication shop prior to installation to ensure proper fit.
- Lay out plate, sheet steel, or other heavy metal and locate and mark bending and cutting lines, using protractors, compasses, and drawing instruments or templates.
- Examine boilers, pressure vessels, tanks, or vats to locate defects, such as leaks, weak spots, or defective sections, so that they can be repaired.
- Shape seams, joints, or irregular edges of pressure vessel sections or structural parts to attain specified fit of parts, using cutting torches, hammers, files, or metalworking machines.
- Inspect assembled vessels or individual components, such as tubes, fittings, valves, controls, or auxiliary mechanisms, to locate any defects.
- Straighten or reshape bent pressure vessel plates or structure parts, using hammers, jacks, or torches.
- Install refractory bricks or other heat-resistant materials in fireboxes of pressure vessels.
- Clean pressure vessel equipment, using scrapers, wire brushes, and cleaning solvents.
- Bell, bead with power hammers, or weld pressure vessel tube ends to ensure leakproof joints.
- Repair or replace defective pressure vessel parts, such as safety valves or regulators, using torches, jacks, caulking hammers, power saws, threading dies, welding equipment, or metalworking machinery.
- Perform preventative maintenance on vehicles and heavy equipment.
- Set out signs and cones around work areas to divert traffic.
- Flag motorists to warn them of obstacles or repair work ahead.
- Drive trucks to transport crews and equipment to work sites.
- Erect, install, or repair guardrails, road shoulders, berms, highway markers, warning signals, and highway lighting, using hand tools and power tools.
- Clean and clear debris from culverts, catch basins, drop inlets, ditches, and other drain structures.
- Drive heavy equipment and vehicles with adjustable attachments to sweep debris from paved surfaces, mow grass and weeds, remove snow and ice, and spread salt and sand.
- Haul and spread sand, gravel, and clay to fill washouts and repair road shoulders.
- Inspect, clean, and repair drainage systems, bridges, tunnels, and other structures.
- Remove litter and debris from roadways, including debris from rock and mud slides.
- Dump, spread, and tamp asphalt, using pneumatic tampers, to repair joints and patch broken pavement.
- Perform roadside landscaping work, such as clearing weeds and brush, and planting and trimming trees.
- Apply poisons along roadsides and in animal burrows to eliminate unwanted roadside vegetation and rodents.
- Measure and mark locations for installation of markers, using tape, string, or chalk.
- Paint traffic control lines and place pavement traffic messages, by hand or using machines.
- Apply oil to road surfaces, using sprayers.
- Inspect markers to verify accurate installation.
- Place and remove snow fences used to prevent the accumulation of drifting snow on highways.
- Blend compounds to form adhesive mixtures used for marker installation.
- Perform preventative maintenance on vehicles and heavy equipment.
- Perform routine maintenance or repairs to restore solar thermal systems to baseline operating conditions.
- Test operation or functionality of mechanical, plumbing, electrical, and control systems.
- Apply weather seal, such as pipe flashings and sealants, to roof penetrations and structural devices.
- Install solar collector mounting devices on tile, asphalt, shingle, or built-up gravel roofs, using appropriate materials and penetration methods.
- Install copper or plastic plumbing using pipes, fittings, pipe cutters, acetylene torches, solder, wire brushes, sand cloths, flux, plastic pipe cleaners, or plastic glue.
- Identify plumbing, electrical, environmental, or safety hazards associated with solar thermal installations.
- Demonstrate start-up, shut-down, maintenance, diagnostic, and safety procedures to thermal system owners.
- Install circulating pumps using pipe, fittings, soldering equipment, electrical supplies, and hand tools.
- Install flat-plat, evacuated glass, or concentrating solar collectors on mounting devices, using brackets or struts.
- Install solar thermal system controllers and sensors.
- Fill water tanks and check tanks, pipes, and fittings for leaks.
- Design active direct or indirect, passive direct or indirect, or pool solar systems.
- Determine locations for installing solar subsystem components, including piping, water heaters, valves, and ancillary equipment.
- Install heat exchangers and heat exchanger fluids according to installation manuals and schematics.
- Apply operation or identification tags or labels to system components, as required.
- Connect water heaters and storage tanks to power and water sources.
- Cut, miter, and glue piping insulation to insulate plumbing pipes and fittings.
- Install plumbing, such as dip tubes, port fittings, drain tank valves, pressure temperature relief valves, or tanks, according to manufacturer specifications and building codes.
- Install monitoring system components, such as flow meters, temperature gauges, and pressure gauges, according to system design and manufacturer specifications.
- Assess collector sites to ensure structural integrity of potential mounting surfaces or the best orientation and tilt for solar collectors.
- Apply ultraviolet radiation protection to prevent degradation of plumbing.
- Perform routine maintenance or repairs to restore solar thermal systems to baseline operating conditions.
- Wind parking meter clocks.
- Enter and retrieve information pertaining to vehicle registration, identification, and status, using hand-held computers.
- Patrol an assigned area by vehicle or on foot to ensure public compliance with existing parking ordinance.
- Write warnings and citations for illegally parked vehicles.
- Appear in court at hearings regarding contested traffic citations.
- Maintain assigned equipment and supplies, such as hand-held citation computers, citation books, rain gear, tire-marking chalk, and street cones.
- Respond to and make radio dispatch calls regarding parking violations and complaints.
- Maintain close communications with dispatching personnel, using two-way radios or cell phones.
- Perform simple vehicle maintenance procedures, such as checking oil and gas, and report mechanical problems to supervisors.
- Observe and report hazardous conditions, such as missing traffic signals or signs, and street markings that need to be repainted.
- Identify vehicles in violation of parking codes, checking with dispatchers when necessary to confirm identities or to determine whether vehicles need to be booted or towed.
- Train new or temporary staff.
- Make arrangements for illegally parked or abandoned vehicles to be towed, and direct tow-truck drivers to the correct vehicles.
- Investigate and answer complaints regarding contested parking citations, determining their validity and routing them appropriately.
- Provide information to the public regarding parking regulations and facilities, and the location of streets, buildings and points of interest.
- Prepare and maintain required records, including logs of parking enforcement activities, and records of contested citations.
- Perform traffic control duties such as setting up barricades and temporary signs, placing bags on parking meters to limit their use, or directing traffic.
- Mark tires of parked vehicles with chalk and record time of marking, and return at regular intervals to ensure that parking time limits are not exceeded.
- Locate lost, stolen, and counterfeit parking permits, and take necessary enforcement action.
- Collect coins deposited in meters.
- Provide assistance to motorists needing help with problems, such as flat tires, keys locked in cars, or dead batteries.
- Assign and review the work of subordinates.
- Wind parking meter clocks.
- Maintain and repair materials, work sites, and equipment.
- Determine the nature of code violations and actions to be taken, and issue written notices of violation, participating in enforcement hearings, as necessary.
- Prepare, organize, and maintain inspection records.
- Investigate complaints and suspected violations regarding illegal dumping, pollution, pesticides, product quality, or labeling laws.
- Determine which sites and violation reports to investigate, and coordinate compliance and enforcement activities with other government agencies.
- Interview individuals to determine the nature of suspected violations and to obtain evidence of violations.
- Inform individuals and groups of pollution control regulations and inspection findings, and explain how problems can be corrected.
- Verify that hazardous chemicals are handled, stored, and disposed of in accordance with regulations.
- Learn and observe proper safety precautions, rules, regulations, and practices so that unsafe conditions can be recognized and proper safety protocols implemented.
- Monitor follow-up actions in cases where violations were found, and review compliance monitoring reports.
- Examine permits, licenses, applications, and records to ensure compliance with licensing requirements.
- Prepare written, oral, tabular, and graphic reports summarizing requirements and regulations, including enforcement and chain of custody documentation.
- Observe and record field conditions, gathering, interpreting, and reporting data such as flow meter readings and chemical levels.
- Determine sampling locations and methods, and collect water or wastewater samples for analysis, preserving samples with appropriate containers and preservation methods.
- Research and keep informed of pertinent information and developments in areas such as EPA laws and regulations.
- Participate in the development of spill prevention programs and hazardous waste rules and regulations, and recommend corrective actions for hazardous waste problems.
- Inspect waste pretreatment, treatment, and disposal facilities and systems for conformance to federal, state, or local regulations.
- Analyze and implement state, federal or local requirements as necessary to maintain approved pretreatment, pollution prevention, and storm water runoff programs.
- Evaluate label information for accuracy and conformance to regulatory requirements.
- Respond to questions and inquiries, such as those concerning service charges and capacity fees, or refer them to supervisors.
- Research and perform calculations related to landscape allowances, discharge volumes, production-based and alternative limits, and wastewater strength classifications, making recommendations and completing documentation.
- Perform laboratory tests on samples collected, such as analyzing the content of contaminated wastewater.
- Inform health professionals, property owners, and the public about harmful properties and related problems of water pollution and contaminated wastewater.
- Review and evaluate applications for registration of products containing dangerous materials, or for pollution control discharge permits.
- Conduct research on hazardous waste management projects to determine the magnitude of problems and treatment or disposal alternatives and costs.
- Prepare data to calculate sewer service charges and capacity fees.
- Maintain and repair materials, work sites, and equipment.
- Perform routine photovoltaic (PV) system maintenance on modules, arrays, batteries, power conditioning equipment, safety systems, structural systems, weather sealing, or balance of systems equipment.
- Install photovoltaic (PV) systems in accordance with codes and standards, using drawings, schematics, and instructions.
- Check electrical installation for proper wiring, polarity, grounding, or integrity of terminations.
- Identify electrical, environmental, and safety hazards associated with photovoltaic (PV) installations.
- Identify installation locations with proper orientation, area, solar access, or structural integrity for photovoltaic (PV) arrays.
- Assemble solar modules, panels, or support structures, as specified.
- Apply weather sealing to array, building, or support mechanisms.
- Install module array interconnect wiring, implementing measures to disable arrays during installation.
- Install required labels on solar system components and hardware.
- Diagram layouts and locations for photovoltaic (PV) arrays and equipment, including existing building or site features.
- Determine materials, equipment, and installation sequences necessary to maximize installation efficiency.
- Test operating voltages to ensure operation within acceptable limits for power conditioning equipment, such as inverters and controllers.
- Determine appropriate sizes, ratings, and locations for all system overcurrent devices, disconnect devices, grounding equipment, and surge suppression equipment.
- Activate photovoltaic (PV) systems to verify system functionality and conformity to performance expectations.
- Identify and resolve any deficiencies in photovoltaic (PV) system installation or materials.
- Visually inspect and test photovoltaic (PV) modules or systems.
- Examine designs to determine current requirements for all parts of the photovoltaic (PV) system electrical circuit.
- Demonstrate system functionality and performance, including start-up, shut-down, normal operation, and emergency or bypass operations.
- Identify methods for laying out, orienting, and mounting modules or arrays to ensure efficient installation, electrical configuration, or system maintenance.
- Measure and analyze system performance and operating parameters to assess operating condition of systems or equipment.
- Program, adjust, or configure inverters and controls for desired set points and operating modes.
- Determine connection interfaces for additional subpanels or for connecting photovoltaic (PV) systems with utility services or other power generation sources.
- Determine photovoltaic (PV) system designs or configurations based on factors such as customer needs, expectations, and site conditions.
- Select mechanical designs, installation equipment, or installation plans that conform to environmental, architectural, structural, site, and code requirements.
- Compile or maintain records of system operation, performance, and maintenance.
- Install active solar systems, including solar collectors, concentrators, pumps, or fans.
- Perform routine photovoltaic (PV) system maintenance on modules, arrays, batteries, power conditioning equipment, safety systems, structural systems, weather sealing, or balance of systems equipment.
- Maintain and coordinate repair of marine machinery and equipment for installation on vessels.
- Design complete hull and superstructure according to specifications and test data, in conformity with standards of safety, efficiency, and economy.
- Supervise other engineers and crew members and train them for routine and emergency duties.
- Study design proposals and specifications to establish basic characteristics of craft, such as size, weight, speed, propulsion, displacement, and draft.
- Perform monitoring activities to ensure that ships comply with international regulations and standards for life-saving equipment and pollution preventatives.
- Oversee construction and testing of prototype in model basin and develop sectional and waterline curves of hull to establish center of gravity, ideal hull form, and buoyancy and stability data.
- Evaluate performance of craft during dock and sea trials to determine design changes and conformance with national and international standards.
- Prepare plans, estimates, design and construction schedules, and contract specifications, including any special provisions.
- Check, test, and maintain automatic controls and alarm systems.
- Design layout of craft interior, including cargo space, passenger compartments, ladder wells, and elevators.
- Evaluate operation of marine equipment during acceptance testing and shakedown cruises.
- Act as liaisons between ships' captains and shore personnel to ensure that schedules and budgets are maintained, and that ships are operated safely and efficiently.
- Conduct environmental, operational, or performance tests on marine machinery and equipment.
- Inspect marine equipment and machinery to draw up work requests and job specifications.
- Prepare, or direct the preparation of, product or system layouts and detailed drawings and schematics.
- Investigate and observe tests on machinery and equipment for compliance with standards.
- Maintain records of engineering department activities, including expense records and details of equipment maintenance and repairs.
- Coordinate activities with regulatory bodies to ensure repairs and alterations are at minimum cost and consistent with safety.
- Design and oversee testing, installation, and repair of marine apparatus and equipment.
- Prepare technical reports for use by engineering, management, or sales personnel.
- Procure materials needed to repair marine equipment and machinery.
- Maintain contact with, and formulate reports for, contractors and clients to ensure completion of work at minimum cost.
- Confer with research personnel to clarify or resolve problems and to develop or modify designs.
- Conduct analytical, environmental, operational, or performance studies to develop designs for products, such as marine engines, equipment, and structures.
- Determine conditions under which tests are to be conducted, as well as sequences and phases of test operations.
- Review work requests and compare them with previous work completed on ships to ensure that costs are economically sound.
- Analyze data to determine feasibility of product proposals.
- Schedule machine overhauls and the servicing of electrical, heating, ventilation, refrigeration, water, and sewage systems.
- Conduct analyses of ships, such as stability, structural, weight, and vibration analyses.
- Establish arrangement of boiler room equipment and propulsion machinery, heating and ventilating systems, refrigeration equipment, piping, and other functional equipment.
- Maintain and coordinate repair of marine machinery and equipment for installation on vessels.